Setting up A Bathtub
Setting up A Bathtub
Blog Article
Listed here below you can find additional exceptional advice involving Tools You Need to Install a New Bathtub .
Setting up a bath tub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old tub with a new one is likewise a reasonably difficult job. If the old tub is conveniently available, the job can move rapidly; if you need to open a wall surface to remove the old bathtub and position the brand-new bathtub, the job is a lot harder. In either situation, the task is within a residence handyman's skills, although you will certainly need an assistant to vacate the old tub as well as embeded in the new one. Make certain you have actually certified yourself for the work and fit trying it. Rather than working with a service provider to take over a halfway-completed job, it is better to think about utilizing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This article will aid you mount a brand-new bathtub in your restroom if you have already gotten a new bathtub and also do not require to change the arrangement of your previous water supply pipes.
Your tools and material list need to comprise the following:
Preparing for the Setup
First of all, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the supplier's guidelines. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to see to it that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the versatile faucet ports to the bottom of both faucets utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final position.
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water system. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the limited gain access to that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. When the supply pipes have been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Using both wooden boards under its feet, position the bathtub in the called for setting. The wood boards are practical in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by checking the level and changing the feet on the bath tub up until the level reads degree.
To install faucets, fit the bottom of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the very same for the other faucet.
Activate the supply of water and also check all joints as well as new pipework for leaks and also tighten them if necessary. Fill up the bathtub and additionally check the overflow outlet and also the normal electrical outlet for leakages.
Finally, take care of the bath paneling as explained in the maker's instruction manual. Tiling as well as securing around the bath tub ought to wait up until the bath tub has been utilized at the very least once as this will resolve it right into its final position.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in place between the tap and the sink. Secure the tap in place with the manufacturer provided backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The previous type ought to be linked to the tap ends first, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom fulfills the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to break a rigid seal, causing the water to pass through the wall surface between the bath and the tiling, bring about difficulties with moisture as well as possible leaks to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes and also cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to allow for the activity experienced when the tub is in usage. The sealant can crack rather very early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious reader on How to Install a Bathtub, I thought sharing that piece of content was essential. Remember to take the opportunity to promote this content if you enjoyed reading it. I truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Book Your Appointment
Report this page